Product ID:PRO-GRIP 5500
MSDS Date:01/01/1985
FSC:8040
NIIN:00N001927
MSDS Number: BCHZT

Emergency Phone: 312-761-4500

Cage: DO270

Telephone: 312-674-7700/312-761-4500

Cage: DO270

METHYL 2-CYANOACRYLATE

CAS: 137-05-3

RTECS: AS7000000

Fraction By Weight: >90%

OSHA PEL 2 PPM/4 STEL

ACGIH TLV: 2 PPM/4 STEL; 9192

Effects of Overexposure:SKIN: WILL BOND ON CONTACT. EYES: WILL BOND &
IRRIT. INHAL: MUCOUS MEMBRANE IRRIT.

First Aid:SKIN: FLUSH W/ WATER; REPEATED SOAKING IN WATER WILL LOOSEN
BONDED SKIN. EYES: FLUSH W/ WATER 15 MIN WHILE HOLDING LIDS
APART;SEE MD. INHAL: REMOVE TO FRESH AIR; SEE MD.

Flash Point:180F,82C,COC
Lower Limits:UNK
Upper Limits:UNK
Extinguishing Media:DRY CHEMICALS, CO*2. WATER SPRY MAY YIELD HAZ
POLYMERIZATION
Fire Fighting Procedures:WEAR SCBA & PROTECTIVE CLOTHING TO PREVENT
CONTACT.
Unusual Fire/Explosion Hazard:PYROLYSIS MAY PRODUCE TOXIC FUMES.
ADHESIVE IN ABSORBENT MAY POLYMERIZE,RAISE TEMP TO AUTOIGNITION.

Spill Release Procedures:ELIMINATE IGNITION SOURCES. USE CLOTH TO
ABSORB ADHESIVES. INCINERATE OR STORE IN CLOSED METAL CONTAINER.
PROTECT EYES,SKIN & CLOTHING FROM CONTACT.

Handling and Storage Precautions:STORE AWAY FROM IGNITION SOURCES.
AVOID CONTACT W/ EYES, SKIN & CLOTHING. AVOID BREATHING VAPORS. USE
VENTILATION TO KEEP VAPOR LEVELS LOW.
Other Precautions:MATERIAL IS COMBUSTIBLE LIQUID. IF SKIN BONDING
OCCURS DO NOT FORCE SEPARATION, SOAK IN WARM WATER.

Respiratory Protection:NIOSH/MSHA APPRVD RESPIRATOR FOR ORGANIC VAPOR
IF NEEDED. (MFR)
Ventilation:MECHANICAL-UNDER MOST CONDITIONS; LOCAL EXHAUST IF NEEDED.
Protective Gloves:POLYETHYLENE
Eye Protection:RECOMMENDED
Other Protective Equipment:COVERALLS OR APRONS TO REDUCE RISK OF
CONTACT.
Supplemental Safety and Health
V.P.@77F,25C < 2 MM HG. VOLATILE BY VOL IS AN APPROX VALUE.

Boiling Pt:B.P. Text:120F,49C
Vapor Pres:<2
Vapor Density:3.8
Spec Gravity:1.1
Evaporation Rate & Reference:NOT DETERMINED
Solubility in Water:NEGLIGIBLE
Appearance and Odor:CLEAR TO SLIGHTLY HAZY LIQUID. PUNGENT,ACRID ODOR
Percent Volatiles by Volume:95

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING MATERIALS CAN CAUSE A VIGOROUS REACTION.
Hazardous Decomposition Products:CO, CO*2, NO*X, & POSSIBLE FORMATION
OF TOXIC FUMES.
Conditions to Avoid Polymerization:ADHESIBES W/ ACIDIC OR BASIC
MATERIALS, PEOXIDES OR WATER.

Waste Disposal Methods:MANUFACTURER RECOMMENDS CONTROLLED INCINERATION
OR LANDFILL. DISPOSAL METHODS MUST BE IAW FEDERAL, STATE & LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.